- Tbs discovery pro go pro imu install#
- Tbs discovery pro go pro imu update#
- Tbs discovery pro go pro imu upgrade#
- Tbs discovery pro go pro imu code#
Only applies when autopilot is not active and TURN ASSIST is disabled. Setting to 0 (the default) disables this feature. This solves the problem of the rudder counteracting turns by partially disabling yaw stabilization when making banked turns. +5 means airplane nose should be raised 5 deg from level Values: -10 - 10 Default: 0 fw_yaw_iterm_freeze_bank_angle Yaw Iterm is frozen when bank angle is above this threshold. This setting only has an effect on NAV modes which take control of the throttle when combined with MOTOR_STOP and is likely to cause a stall if fw_min_throttle_down_pitch isn't set correctly or the pitch estimation is wrong for fixed wing models when not set to ALL_NAV nav_rth_climb_first New: ON_FW_SPIRAL platform_type Default: MULTIROTOR receiver_type Default: target rssi_source Default: AUTO New Settings Setting Description dji_speed_source Sets the speed type displayed by the DJI OSD: GROUND, 3D, AIR Default: GROUND dshot_beeper_enabled Whether using DShot motors as beepers is enabled Default: TRUE dshot_beeper_tone Sets the DShot beeper tone Values: 1 - 5 Default: 1 fw_d_pitch Fixed wing rate stabilisation D-gain for PITCH Default: 0 fw_d_roll Fixed wing rate stabilisation D-gain for ROLL Default: 0 fw_d_yaw Fixed wing rate stabilisation D-gain for YAW Default: 0 fw_level_pitch_trim Pitch trim for self-leveling flight modes. When set to ALL_NAV (default) the navigation system will take over the control of the motor completely and never allow the motor to stop even when the throttle is low. When set to AUTO_ONLY the navigation system will only take over the control of the throttle in autonomous navigation modes (NAV WP and NAV RTH).
When set to OFF_ALWAYS the navigation system will not take over the control of the motor if the throttle was low even when failsafe is triggered. Refer to docs Changed Settings Setting Description blackbox_device Default: target log_level Default: ERROR nav_overrides_motor_stop When set to OFF the navigation system will not take over the control of the motor if the throttle is low (motor will stop).
Tbs discovery pro go pro imu upgrade#
Tbs discovery pro go pro imu install#
Download and install the new configurator.You can copy osd, aux, serial, and mixer settings, as well as accelerometer and magnetometer calibration values from INAV 2.6, but other settings should be tuned again. To get the best performance set up your aircraft from scratch. We suggest NOT to do a full diff or dump upgrade. Upload the updated font of your choosing from the OSD tab.
Tbs discovery pro go pro imu update#
A font file update is required to use the new symbols and avoid an invalid font warning. The OSD fonts have been improved and there are several new symbols. Check the adjustments tab in the configurator after restoring a diff to makes sure they are set up correctly. This breaks compatibility with diffs from previous releases. There are now separate adjustments for D and CD/FF gains.
Tbs discovery pro go pro imu code#
The supporting code will be retained for a few more releases, but will not be maintained and is not guaranteed to build or work properly in the future. If you are still using F3 boards, please migrate to F4 or F7. STM32 F3 flight controllers like Omnibus F3 or SP Racing F3 are no longer supported in INAV. Tested and suggested hardware can be found here Important Notes F3 Removal Your contribution from the past month has been very welcome! Thanks!
Please continue to support developers, for free, by checking out from the following stores after having clicked on the following links: Support us on Banggood Get in touch with other pilots, share experiences, suggestions and ask for help on: INAV Official on Telegram INAV Official on Facebook Please carefully read all of this document for the best possible experience and safety.
0 kommentar(er)
